Botanicals hub
Your plant library, clinic, and notebook — in one place
Start with the list below to look up any plant's care, propagation, and grafting. Use Diagnose to turn what you see into a step-by-step plan, and open “See how it plays out” to watch a problem unfold — and see how treating it, ignoring it, over-treating it, or over-caring for it each change the ending. Everything you save lands in History, where you can search it, ask across it, and export only what you choose. Timing is for the NC Piedmont, Zones 7–8, unless a plant says otherwise. The full hydrangea guide — your photos, stem, and colour lab — is still here in full, further down the page and as the first entry in the library.
Plant library
List of botanicals — ornamentals & vegetables
Search by name or need — try “shade,” “tomato,” “cuttings,” or “grafting.” Tap any plant to open its full panel: care, propagation, grafting, common problems, and treatments.
Diagnose & prepare plans
Diagnose a problem — get a plan
Pick the plant, pick what you see, add any notes. You'll get the most likely causes in plain words, each with a step-by-step treatment plan — home fixes first (water, spacing, cleaning up, pruning), then product options. Product amounts are never guessed here: they always read “Per label — follow the product label,” with a space for you to type what your own label says.
Interactive scenarios
See how it plays out
Every plant problem belongs to one of four families — Disease, Pests, Fungus, and Nutrients — and each family wears its own badge everywhere in this hub. Pick a scenario below, step through how the problem starts and how it grows when nobody notices, then choose how to respond: treat it right, don’t treat it, over-treat it, or over-care for it. The plant-health meter and the little drawn plant change as the story does. Same rule as everywhere here: home fixes first, and any product is used per label — no rates are ever guessed.
Drag the slider or use Back / Next to walk the timeline. Stage 1 is the problem unnoticed; Stage 2 is what weeks of nothing turn it into. After that, the ending is up to the path you choose.
What you’d see
What’s happening
Your move
Choose how you respond
History — saved in this browser
History, search & ask
Every diagnosis, plan, and note you save is kept here on this device, with its date, plant, and title. Search filters your history. Ask searches your history and the plant library together — try “tomato spots” or “rose yellow.”
Add a note or plan by hand
Share · Download · Export
Take out only what you choose
Tick the box on any plant, diagnosis, scenario outcome, or history entry to select it. Nothing leaves this page until you press a button below — and only the ticked items go.
Share copies a clean plain-text version and opens your device share sheet where available. Download saves the selected items as a readable Markdown file. Export combines everything selected into one dated Botanicals file.
Start here
Tap the stem, part by part
This is your own bare stem (photo 1693): about 25 cm tall, a green broccoli-like flower bud on top, pairs of buds at four joints down the stem, and two long side shoots at the very bottom. The six numbered points and the three cut lines are marked right on your photo. Tap a number — or use the buttons — to see what to do at each spot. Prefer a clean drawing instead? Switch to the Drawing view.
Your photo — compare its joints and buds with the drawing. Nothing is uploaded or saved; it never leaves this page.
The job
Two new plants from one stem, in 4 steps
Your stem has four healthy joints, so it splits into two cuttings — a top half (Cutting A) and a bottom half (Cutting B). Each one is planted the same way.
Take the flower head off
Wipe your pruners or a razor blade with rubbing alcohol (70% isopropyl alcohol) first. Then cut the green flower head off, just above the first joint — about 1.5 cm below the cluster. This is Cut 1.
Why: clean tools don't carry disease from plant to plant, and the flower head is the #1 reason cuttings fail — it drains the stem (see point 1 on the diagram).
Split the stem into two cuttings
Cut 2: cut straight across, halfway between the 2nd and 3rd joints. Cut 3: cut at a 45° angle, about 0.5 cm below the bottom joint. Keep both cuttings right-side up the whole time.
Why: a stem “remembers” which end is up — roots only grow from the bottom end, so never plant one upside down.
Scrape and dip
On each cutting, lightly scrape a thin strip of the outer skin, about 1 cm long, off one side of the bottom joint until you see bright green underneath. Then dip the base in rooting hormone gel or powder (strength 1,000–3,000 ppm).
Why: the bright green layer just under the skin is the living layer that grows roots (the cambium), and rooting hormone is a concentrated copy of the plant's own “grow roots” signal (an auxin, called IBA) — it tells that layer to get started.
Pot it and put a dome on it
Fill a pot with a half-and-half mix of perlite and peat or coco coir. Push the cutting in so the bottom joint is buried about 2 cm deep and the top joint sits about 2 cm above the soil. Cover with a clear plastic dome or bag. Keep it at 20–23 °C in bright light, out of direct sun.
Why: a cutting has no roots to drink with yet, so the dome holds the moisture in the air around it while roots form — expect them in 21–28 days.
Know your stem
Your stem at three stages
The same plant looks very different across the season. Pick a stage to see what it means for taking cuttings.
Your photos
From the stand — the rest of your photos
The same hydrangea stand, out in the real world: the long cane before and after it came off the bush, and the cuttings it turned into. Tap any photo to see it big.
Try it
Flower colour lab — you choose blue or pink
Bigleaf hydrangeas use one single pigment for both blue and pink flowers. What changes the colour is whether the plant can pick up aluminum from the soil — and that depends on how acidic the soil is. That acidity is measured as pH: a 0–14 scale of how acidic something is — lower numbers mean more acidic. Drag the slider and watch the flower.
Go further
Three more things this stem can do
Split one stem into 8 mini clones
4 joints × 2 buds each = 8 new plants
Look at any joint on the stem: it always has two buds, one on each side, facing each other. Nurseries use that to multiply a plant fast. Cut the stem into 4 short pieces, one joint per piece. Then split each piece lengthwise, straight down the middle, between the two buds. Now you have 8 halves, each with its own bud.
Lay each half flat — cut side down, bud facing up — pressed halfway into damp moss (sphagnum moss) in a sealed tray, under lights about 16 hours a day.
The long cut face exposes the stem's living layer along its whole length. It first grows a protective scab-like tissue (callus), then roots burst out along the cut — usually within about 3 weeks.
Keep the flower heads you cut off — forever
Don't throw the flower heads away. What look like petals are actually tough, leaf-like parts (sepals), so hydrangea blooms preserve far better than most flowers.
The glycerin method: crush the woody base of the stem so it can drink, then stand it in a mix of 1 part vegetable glycerin to 2 parts hot water for about 10 days. The stem draws the glycerin up into the flower head, where it takes the place of the water.
Water dries out and leaves blooms brittle. Glycerin doesn't evaporate, so the flower parts stay soft and flexible — the blooms keep for years instead of weeks.
Make colour-changing ink from old blooms
Simmer the cut-off florets from a faded flower head in 100 mL of water with 1 teaspoon of alum for 20 minutes, then strain. You get a watercolour ink made from the flower's own pigment — the same pigment that makes the blooms blue or pink in the soil.
Paint with it, then try this: brush a little baking soda solution over one patch and it shifts teal-blue; brush lemon juice over another and it turns magenta.
The pigment changes its shape — and so its colour — depending on acidity, exactly like it does in the soil in the colour lab above. Baking soda makes it less acidic; lemon juice makes it more acidic. The alum helps the colour grip the paper.
No jargon left behind
Words, translated
Every technical word used in this guide, in plain language.